Electric Counselor

How to Change a Dewalt Miter Saw Blade

To change the blade on a DeWalt Miter Saw, you will need to gather a few tools. These include an adjustable wrench, protective gloves and eyewear, and the new saw blade. Begin by unplugging your miter saw from any power source.

Then use the wrench to loosen and remove the bolts that hold the old blade in place. Carefully lift off the old blade being careful not to touch its sharp edges with unprotected skin or clothing. Place it aside safely out of reach of children or pets until disposal can be arranged.

Securely install your new sawblade onto the arbor shaft using all necessary bolts included with it before tightening them by hand first then with your wrench. Check for wobble at high RPMs before plugging back into power source for use.

  • Step 1: Unplug the miter saw and remove the blade guard. This is an important safety step to ensure that you do not accidentally activate the saw while changing the blade.
  • Step 2: Use a wrench or socket to loosen and remove the arbor nut, which holds the blade in place on its spindle. Depending on your model of Dewalt miter saw, this may be located at either end of the spindle shaft, above or below where it exits from beneath the table surface.
  • Step 3: Lift off any washers that were under the arbor nut and set them aside for re-use when you install a new blade. Withdrawing these allows you to slip off and discard your old, dulled miter saw blade from its mounting position.
  • Step 4: Place a new Dewalt miter saw blade onto its spindle so that it is properly aligned with any remaining washers underneath it as well as with marks indicating direction of rotation on both sides of its hub (if present). Push down firmly until fully seated against those components.
  • Step 5: Replace all washers and screws removed earlier, twisting securely into place by hand before using a wrench or socket to further tighten them if necessary; make sure they are snug but not overly tight since over tightening can affect performance negatively while also increasing wear on tool parts due to friction build up within their threads over time. Reinstall your guard unit afterwards before testing out your newly installed cutting edge!

How to Change a Mitre Saw Blade | Dewalt Chop Saw Blade Change | DWS779

How Do You Change the Blade on a Dewalt 20V Miter Saw?

Changing the blade on a DeWalt 20v miter saw is a relatively easy process. Start by unplugging the saw and removing the old blade by loosening the arbor nut at the center of your saw’s blade using an appropriately sized wrench or socket. Once removed, carefully clean out any dust buildup from around the arbor area before inserting your new blade with its teeth facing forward in a clockwise direction.

Securely fasten your new blade to the arbor using an appropriately sized wrench or socket and tighten it until snug but not overly tight. Finally, plug in your saw and you are ready to use it again!

How Do You Change the Blade on a Dewalt Dw715 Miter Saw?

Changing the blade on a DeWalt dw715 miter saw is easy to do, although it should always be done with caution.

First, make sure the saw is unplugged and all moving parts have stopped. Loosen the arbor nut by turning it counterclockwise until it can be removed completely.

Carefully remove the old blade and install the new one, making sure that it’s lined up correctly with its teeth facing downward towards you. Reinstall the arbor nut and tighten securely using a wrench or adjustable wrench depending on your model.

Finally, plug in your saw again to test out your newly installed blade!

How Do You Remove a Dewalt Saw Blade?

To remove a DeWalt saw blade, you will need to start by disconnecting the power supply for safety. Then locate and loosen the spindle lock located at the front of your saw. Once it is loose, rotate the blade to align with its slot in the arbor nut.

Now you can turn and unscrew the arbor nut until it comes away from its housing on the frame of your saw. Once this is done, gently lift up on one side of your saw blade to release it from its position within your saw’s housing before carefully lifting it away and setting aside for later use or disposal as needed.

How to Change a Dewalt Miter Saw Blade

Credit: thearchitectsdiary.com

How to Change Dewalt Miter Saw Blade Without Tool

Changing the blade of a DeWalt miter saw without using any tools is fairly simple. First, you will need to unplug the saw from its power source and remove the guard covering the blade. Once that is done, loosen up the arbor nut by hand with counterclockwise turns until it’s loose enough to be removed by hand.

Then take off both washers and pull out your old blade before replacing it with a new one. Make sure that all parts are properly installed before tightening down on the arbor nut again and reattaching your guard overtop of your new blade!

Changing Blade on Dewalt 10 Inch Miter Saw

Changing the blade on a DeWalt 10 Inch Miter Saw is relatively straightforward. First, unplug the saw and turn off the power switch. Then, use an Allen wrench to loosen and remove any screws that are holding the blade guard in place.

Once you’ve done this, carefully lift off the old blade and insert your new one – making sure it is securely fastened with bolts or clamps – before replacing the guard. Finally, plug in your miter saw and make sure all parts are properly secured before turning it back on for safe operation.

How to Change Blade on Dewalt Miter Saw Dw713

Changing the blade on a Dewalt miter saw Dw713 is easy and takes just a few minutes. Begin by unplugging your saw from the power source, then use an Allen wrench to loosen and remove the bolts that hold the arbor nut in place. Next, spin off the arbor nut to release the old blade.

Install your new blade onto its mounting hole using a wrench to secure it firmly in place before finally replacing both washers and their original bolts back into their respective spots. Finally, plug your saw back into its power source and you are ready to start cutting again!

Dewalt Dcs777 Blade Change

The Dewalt Dcs777 is a powerful circular saw that comes with an easy-to-use blade change system. The blade can be quickly and easily changed by simply releasing the lower guard lever, removing the old blade, inserting a new one into the arbor hole, and tightening it in place with the included Allen wrench. Once installed, this saw has plenty of power to tackle tough jobs around your home or workshop.

Whether you’re building furniture, trimming trees or making other cuts for various projects, this saw will help you get them done quickly and efficiently.

Change Blade Dewalt Miter Saw Dw716

The DeWalt DW716 miter saw is an excellent choice for professionals and DIYers alike. It offers a powerful 15 amp motor with 4,000 RPM that can handle almost any cutting job you throw at it. The tool also features a 12-inch carbide blade that gives precise results when making angled cuts.

Additionally, the saw has adjustable stainless steel miter detents to ensure accuracy when making repetitive cuts or angles. With its wide range of features and high quality construction, the DeWalt DW716 miter saw is sure to be a great addition to your workshop!

How to Change Blade on Dewalt Circular Saw

Changing the blade on a DeWalt circular saw is relatively easy and can be done in just a few steps. First, unplug the saw from any power source and make sure it has cooled off enough to handle safely. Then, loosen the screw or bolt that secures the blade with an appropriate tool.

Next, carefully remove the old blade from its housing and replace it with a new one. Finally, tighten the screw or bolt securely to ensure that your new blade is properly secured before plugging in your saw again and resuming use.

Dewalt Blade Change Tool

The Dewalt Blade Change Tool is the perfect tool for any DIYer or professional. This handy device allows you to quickly and easily change out blades on your circular saw, reciprocating saw, jig saw and more. It features a simple push button release that makes blade changes fast and easy, while its ergonomic design ensures comfortable use.

Additionally, it’s compatible with all brands of blades so you can find one that works best for your project. With this tool in your arsenal, you’ll be able to tackle any job with confidence!

Dewalt Miter Saw Blade Change Tool

The Dewalt Miter Saw Blade Change Tool is an essential tool for any woodworker and a great addition to your miter saw. This tool makes it easy to quickly and safely change out blades on your miter saw without having to use multiple tools or complicated techniques. It’s constructed of durable steel, so you can be sure that it will last for many years with proper care.

With its convenient size, you can take this blade changing tool anywhere with ease.


In conclusion, changing a DeWalt miter saw blade is a relatively easy process that can be completed in just a few steps. It is important to remember to wear safety goggles and use the correct tools for loosening and tightening the blade screws. Taking these necessary precautions will ensure your safety as you replace an old or dulled miter saw blade with a new one.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top